Power-bell 200x200 - 2000x2000

cod.C3045

PRESSURE GLAZE APPLICATION SYSTEM
Waterfall application machine made of stainless steel aisi 304 with internal chamber coated with anti-abrasion rubber. The machine has been studied for the application of engobes, glazes, glazes with micro-grains and vitreous crystallines. It is fed by a stirrer tank with pump. The machine is equipped with a filter at the entry with bubble-proof system and manual venting to eliminate the air inside the chamber. It is complete of electric control panel (control flux) that controls the capacity flow and by inverter regulator it keeps constant the weight parameters that have been set. Pump for feeding of “power-bell” machine. It is available also in the version for high viscosity glazes and glazes with micro-grains.

Glazing



by admin_ricoth

No-Clean

cod.C3054

Device for the interruption of the conveyor belts under the application of glaze, engobe done by bell or “power-bell”. This application permits to avoid the transport of the glaze on the belts that consequently dirts the surface under the tile. The machine is controlled by two geared motors synchronized by inverter.

New waterproofed head pulleys with double seals.

cod.C3054

NO-CLEAN
Two belt version.

cod.C3054

NO-CLEAN
4 belt version, also with curve radius for bell.

cod.C3054

NO-CLEAN
Inclined version 2/4 belts.

Glazing



by admin_ricoth

Bell

cod.C3020

460mm, 660mm, 800mm, 1000mm, 1200mm, 1500mm, 1800mm (new)

System for the gravity application of glazes and engobes.

Glazing



by admin_ricoth

Grado temperature control

cod.F0212

“GRADO” Is a tile temperature control device using infrared off-contact and with environment temperature compensation. This device can be combined to the water cabin with automatic nozzles opening and closing to obtain the desired temperature.

 

Glazing



by admin_ricoth

Brushing

cod.B0640

UPPER BRUSH WITH CONTRA-ROTATING BELTS.
It is used to remove the powder and the residual burrs caused by the pressing process. Upper brush with double motor and contra-rotating belts for glazing line.

cod.B0641

LOWER BRUSH  CONTRA-ROTATING BELTS
Lower brush with double motor and contra-rotating belts for glazing line.

cod.B0640

UPPER BRUSH WITH CONTRA-ROTATING BELTS FOR PRESS EXIT. 
Upper brush with double motor and contra-rotating belts for press exit.

cod.B0620 – cod.B0624

BRUSH WITH SINGLE AND DOUBLE MOTOR.
Rollers upper-lower brush.

cod.B0608

SINGLE DISK BRUSH.
Single disk upper brush.

Glazing



by admin_ricoth

Flux equal-spacing machine

cod.A5858

Electronic model with 2/3 inverters to space out uniformly the tiles flow without contact by decelerating the machine motors.

Glazing



by admin_ricoth

Bell controller

cod.C3050

Bell feeding automatic system that eliminates the glaze variation on the tile usually caused by the changing of density and viscosity. It is complete of electric panel with inverter and transducer for the flow control and management.

Glazing



by admin_ricoth

Curve

cod.A5402

Composed by painted steel structure. It is used for the tiles flowing through tape, rollers, belts on polyzene and plastic belt. Bi-directional lifting belt curve.

cod.A5412

Curve with wear-proof plastic belt. Turning, lifting and bi-directional curve.

cod.A5408

Curve with wear-proof plastic belt. Lifting and bi-directional curve.

cod.A5314

Curve 15° to 180° with wear-proof plastic belt.

cod.A5302

PVC belt curve

cod.A5320

Rubber roller curve.

cod.A5266 – cod.A5216

Belt curve.

Linee e accessori



by admin_ricoth